Pomoc TS-X53B / TS-X53Be uwalony BIOS błędną metodą aktualizacji lub wsadem

Kreonium

System Engineer
Q Specialist
14 Wrzesień 2018
108
6
18
61
QNAP
TS-x53B
Ethernet
1 GbE
Zrobiłem upgrade biosu. Niby wszystko przebiegło normalnie a teraz mam "System Booting".
Co mnie podkusiło z tym update to nie wiem :/
 
Nie należę do forumowych/życiowych pieniaczy. Jednak serwer to ważna cześć środowiska sieciowego. Wolałbym dostać po tygodniu info,że zjebałem i serwer szrot niż 5 tygodni czekać z informacją na stronie : wysłane do gwaranta. Dla mnie to niepoważne, bez względu na finał sprawy.
 
W celu dopełnienia formalności (U42) chip Winbond jest od portu QA. Natomiast bios znajduje się w prawym górnym rogu (U4).

23265.png
Hi,

Can you please post the power rails/test points page? I'm trying to figure of if my 463Be is brain dead(dead CPU) or a power IC died on the MB.

Thanks!
 
My device is just red blinking, not passing the POS, no beep, no display. I would like to try to read the bios, compare it or reflash.

try the part with this resistor 100ohm
Thanks, but mine is TS-453b, not PRO, different device.
Anyway, I checked CLK on PIN1 of the LPC_CN1, but there is no clock at all. It might be elsewhere but I am not able to trace it.
W celu dopełnienia formalności (U42) chip Winbond jest od portu QA. Natomiast bios znajduje się w prawym górnym rogu (U4).

23265
Hi,

Can you please post the power rails/test points page? I'm trying to figure of if my 463Be is brain dead(dead CPU) or a power IC died on the MB.

Thanks!
Have you been able to find the testing points table fot TS-453B? Any progress in repairing of your device?
 
Thanks, but mine is TS-453b, not PRO, different device.
according to https://forum.qnap.com/viewtopic.php?f=45&t=135089&start=180
also another models like TS-251 - it works for them.

Yes, both TS-453Pro and TS-251 have the same processor. As the defect is in the processor, it might be fixed by the same fix. But TS-453b has different processor.
I am now waiting for delivery of the 1.9V SPI flash adapater (as my Beeprog does not support it) to check the BIOS. I also tried for a while to capture the SPI by logic analyzer but did not get clear result, i will try later again.
Just an update. I finally get the 1.8V adapter so I flashed QY47AR14 and QY47EF18 but the result is the same, TS-453b is just red blinking, not passing the POS, no beep, no display.
 
Just an update. I finally get the 1.8V adapter so I flashed QY47AR14 and QY47EF18 but the result is the same, TS-453b is just red blinking, not passing the POS, no beep, no display.

I have same problem, i changed main processor and ITE chip, flashed new bios and EC and same problem - red led slowly blinks but i menaged that it is problem with power i think because when i manually drive U2 transistor then red LED started to blink faster :)
 
I have same problem, i changed main processor and ITE chip, flashed new bios and EC and same problem - red led slowly blinks but i menaged that it is problem with power i think because when i manually drive U2 transistor then red LED started to blink faster :)

Good to hear I am not alone. :) Do you see any clock signal on the LPC_CN1 connector ?
It has been discussed here as well, but I did not try to attach logic analyzer to the ITE chip yet.
[How To] Recover no beep / dead Intel based Qnap x53/x51 (2014~2016?) - Page 2 - QNAP NAS Community Forum
 
Good to hear I am not alone. :) Do you see any clock signal on the LPC_CN1 connector ?
It has been discussed here as well, but I did not try to attach logic analyzer to the ITE chip yet.
[How To] Recover no beep / dead Intel based Qnap x53/x51 (2014~2016?) - Page 2 - QNAP NAS Community Forum
Hello, i see 1,8V and 33,3Mhz on pin 1 on lpc connector when i manually switch mosfet U2 thats all i can do now and power led starts blinking fast but nothing else happends :(
 
Do you mean this U2? Please post how exactly do you drive it, I will try the same on my device.

u2.jpg

Hello, i see 1,8V and 33,3Mhz on pin 1 on lpc connector when i manually switch mosfet U2 thats all i can do now and power led starts blinking fast but nothing else happends :-([/QUOTE]

Hi, any update?
 
Do you mean this U2? Please post how exactly do you drive it, I will try the same on my device.

36374.jpg

Hello, i see 1,8V and 33,3Mhz on pin 1 on lpc connector when i manually switch mosfet U2 thats all i can do now and power led starts blinking fast but nothing else happends :-(

Hi, any update?[/QUOTE]

Hi, write mail to me to george2002@tlen.pl :)
 

Użytkownicy znaleźli tą stronę używając tych słów:

  1. george2002
  2. ts-453 bios
  3. ts-453b
  4. ts-453pro
  5. TS-X53B
  6. ts-453b red light