Pomoc TS-X53B / TS-X53Be uwalony BIOS błędną metodą aktualizacji lub wsadem

[Kreonium]

Zrobiłem upgrade biosu. Niby wszystko przebiegło normalnie a teraz mam "System Booting".
Co mnie podkusiło z tym update to nie wiem :/

 

[lukaszzsch]

Nie należę do forumowych/życiowych pieniaczy. Jednak serwer to ważna cześć środowiska sieciowego. Wolałbym dostać po tygodniu info,że zjebałem i serwer szrot niż 5 tygodni czekać z informacją na stronie : wysłane do gwaranta. Dla mnie to niepoważne, bez względu na finał sprawy.

 

[Usunięty użytkownik pigers]

Dla mnie to niepoważne, bez względu na finał sprawy.

i moje pytanie : na ch00j robisz update biosu skoro wszystko działa ?

poważnie - w aucie też silnik wymieniasz bo poduszki się starły ? ....

 

[Silas Mariusz]

Dobra koniec dyskusji. Z info jakie mam ma być wymieniony na nowy.

 

[lukaszzsch]

Dobra koniec dyskusji. Z info jakie mam ma być wymieniony na nowy.

Dzięki!

 

[lukaszzsch]

Serwer wymieniony na nowy. Dzięki za wszystko.

 

[sharpli]

Just wondering where can we download QY47AR56 bios image?

 

[ochykysh]

W celu dopełnienia formalności (U42) chip Winbond jest od portu QA. Natomiast bios znajduje się w prawym górnym rogu (U4).

Hi,

Can you please post the power rails/test points page? I'm trying to figure of if my 463Be is brain dead(dead CPU) or a power IC died on the MB.

Thanks!

 

[Silas Mariusz]

I can't help you with that.

 

[kibkib]

Just wondering where can we download QY47AR56 bios image?

I Have the same question. Where is it possible to download the TS-453b bios file (QY47AR56).
My device is just red blinking, not passing the POS, no beep, no display. I would like to try to read the bios, compare it or reflash.
Thank you

 

[max85]

Panowie/Panie - wlasnie dzieki QNAP TS-453 Pro stuck on "SYSTEM BOOTING" - Page 12 - QNAP NAS Community Forum naprawilem swojego TS-430pro

tu moj wątek: Udzielamy pomocy - TS-453Pro - reanimacja

/My TS-430pro reanimated successfully!
check my link.

To solve - 1x 100ohm resistor

 

[kibkib]

Just wondering where can we download QY47AR56 bios image?

I Have the same question. Where is it possible to download the TS-453b bios file (QY47AR56).
My device is just red blinking, not passing the POS, no beep, no display. I would like to try to read the bios, compare it or reflash.
Thank you

I found this one. Hoep it is the right one.
http://download.qnap.com/Storage/tsd/bios/QY47AR56.zip

 

[max85]

My device is just red blinking, not passing the POS, no beep, no display. I would like to try to read the bios, compare it or reflash.

try the part with this resistor 100ohm

 

[kibkib]

My device is just red blinking, not passing the POS, no beep, no display. I would like to try to read the bios, compare it or reflash.

try the part with this resistor 100ohm

Thanks, but mine is TS-453b, not PRO, different device.
Anyway, I checked CLK on PIN1 of the LPC_CN1, but there is no clock at all. It might be elsewhere but I am not able to trace it.

W celu dopełnienia formalności (U42) chip Winbond jest od portu QA. Natomiast bios znajduje się w prawym górnym rogu (U4).

Hi,

Can you please post the power rails/test points page? I'm trying to figure of if my 463Be is brain dead(dead CPU) or a power IC died on the MB.

Thanks!

Have you been able to find the testing points table fot TS-453B? Any progress in repairing of your device?

 

[max85]

Thanks, but mine is TS-453b, not PRO, different device.

according to https://forum.qnap.com/viewtopic.php?f=45&t=135089&start=180
also another models like TS-251 - it works for them.

 

[kibkib]

Thanks, but mine is TS-453b, not PRO, different device.

according to https://forum.qnap.com/viewtopic.php?f=45&t=135089&start=180
also another models like TS-251 - it works for them.

Yes, both TS-453Pro and TS-251 have the same processor. As the defect is in the processor, it might be fixed by the same fix. But TS-453b has different processor.
I am now waiting for delivery of the 1.9V SPI flash adapater (as my Beeprog does not support it) to check the BIOS. I also tried for a while to capture the SPI by logic analyzer but did not get clear result, i will try later again.
Just an update. I finally get the 1.8V adapter so I flashed QY47AR14 and QY47EF18 but the result is the same, TS-453b is just red blinking, not passing the POS, no beep, no display.

 

[george2002]

Just an update. I finally get the 1.8V adapter so I flashed QY47AR14 and QY47EF18 but the result is the same, TS-453b is just red blinking, not passing the POS, no beep, no display.

I have same problem, i changed main processor and ITE chip, flashed new bios and EC and same problem - red led slowly blinks but i menaged that it is problem with power i think because when i manually drive U2 transistor then red LED started to blink faster

 

[kibkib]

I have same problem, i changed main processor and ITE chip, flashed new bios and EC and same problem - red led slowly blinks but i menaged that it is problem with power i think because when i manually drive U2 transistor then red LED started to blink faster

Good to hear I am not alone. Do you see any clock signal on the LPC_CN1 connector ?
It has been discussed here as well, but I did not try to attach logic analyzer to the ITE chip yet.
[How To] Recover no beep / dead Intel based Qnap x53/x51 (2014~2016?) - Page 2 - QNAP NAS Community Forum

 

[george2002]

Good to hear I am not alone. Do you see any clock signal on the LPC_CN1 connector ?
It has been discussed here as well, but I did not try to attach logic analyzer to the ITE chip yet.
[How To] Recover no beep / dead Intel based Qnap x53/x51 (2014~2016?) - Page 2 - QNAP NAS Community Forum

Hello, i see 1,8V and 33,3Mhz on pin 1 on lpc connector when i manually switch mosfet U2 thats all i can do now and power led starts blinking fast but nothing else happends

 

[kibkib]

Do you mean this U2? Please post how exactly do you drive it, I will try the same on my device.

Hello, i see 1,8V and 33,3Mhz on pin 1 on lpc connector when i manually switch mosfet U2 thats all i can do now and power led starts blinking fast but nothing else happends :-([/QUOTE]

Hi, any update?

 

[george2002]

Do you mean this U2? Please post how exactly do you drive it, I will try the same on my device.

Hello, i see 1,8V and 33,3Mhz on pin 1 on lpc connector when i manually switch mosfet U2 thats all i can do now and power led starts blinking fast but nothing else happends :-(

Hi, any update?[/QUOTE]

Hi, write mail to me to george2002@tlen.pl